Привет, друг!

Зарегистрируйся, если хочешь купить что-то для своих любимцев

AidaHakala's профиль


Profile

  • Full name: AidaHakala
  • Адрес: Via Carlo Alberto 39, Carbonate
  • Местоположение: Uraz, lubuskie, Ukraine
  • Вебсайт: https://www.pinterest.com/adamssloan494/
  • User Description: Discuss with that product’s installation sheet for directions. Twist and remove mounting bracket to insert battery. Product Description Lutron’s ceiling-mounted Occupancy Sensors are wireless, battery-powered, passive infrared (PIR) units that robotically management lights via RF communication with a dimming or switching device. These Sensors detect the heat from individuals transferring within an space to find out when the area is occupied. The Sensors then transmit the suitable commands to the related dimming or switching gadget to show the lights on or off mechanically, providing both convenience and distinctive energy savings. Sensor doesn't carry out satisfactorily from this location, it may be moved to 1.4 Ifanother location by pulling the Sensor straight down and repeating steps 1.Three and 1.4. 1.5 If the Sensor’s performance is satisfactory, it needs to be completely connected to the ceiling tile, as described in section G. Permanent Mounting. Non permanent Solid Ceiling Mounting Use this procedure if the Sensor can be mounted on a stable, continuous ceiling floor equivalent to drywall, plaster, concrete, or wood. Two 3M™ Command™ adhesive strips are provided for quickly mounting and testing the Sensor on clean, solid ceiling surfaces. These strips are designed for straightforward, damagefree removal and usually are not reusable. These strips should not be used for permanently mounting the Sensor (see section G. Permanent Mounting ). Fastidiously observe the removal instructions under to ensure the ceiling is just not damaged during removal. Word: Don't use the adhesive strips on ceiling tiles, as they may probably cause harm to the tile upon removing. Easy-to-observe Directions Set-Up To ensure that the Sensor to function properly, it must first be set up with a corresponding dimming or switching machine. The process for organising a Sensor with a Maestro Wireless® (MRF2- solely) Dimmer or Digital Switch is detailed below. P/N 041-172a 2.1 Peel the pink "Command Strips" liner off of one of many adhesive strips and apply the strip to the flat aspect of the mounting bracket as shown in the diagram. Observe: Don't cowl the bracket’s screw holes because they are going to be used to mark screw hole places on the ceiling. Setting up a Sensor with a Maestro Wireless Dimmer or Electronic Swap Dimmer Key Features · Low Upkeep. 10-12 months battery life. Convenient low-battery indicator. · Multiple Devices. Up to 3 Sensors can work collectively to manage lights for broader protection in large spaces. Every Sensor may be added to up to 10 receiving devices. Sensor Operation Occupancy Model - The Sensor will mechanically turn the lights on when the area is occupied and automatically flip the lights off after the area is vacated. The Sensor will routinely turn the lights off after the house is vacated. There is a built-in 15-second vacancy grace interval that begins when the lights are routinely turned off, during which the lights will robotically flip again on in response to motion. This grace interval is supplied as a safety and comfort characteristic in the event that the lights flip off whereas the room continues to be occupied, so that the person doesn't need to manually turn the lights again on. After 15 seconds, the grace period expires and the lights should be manually turned on. This Sensor is part of a system and can't be used to manage a load without a compatible dimming or switching gadget. Confer with the instruction sheets of the receiving machine(s) for installation info. The Sensor may be put in as much as 60 ft (18.Three m) away from the related dimming or switching machine(s) if they are in direct line of sight. If there are walls or other barriers between the Sensor and receiving gadget(s), the Sensor needs to be positioned within 30 ft (9.1 m). Warning: This product should not be used to manage tools which might create hazardous situations, akin to entrapment, if operated by accident. Sensor in a location the place it has a broad view outdoors the supposed area. If that is unavoidable, the lens might be masked to dam the view of undesired areas (discuss with part I. Lens Masking). This warranty is in lieu of all other express warranties, and the implied warranty of merchantability is restricted to one 12 months from purchase. This warranty does not cover the price of installation, elimination or reinstallation, or damage ensuing from misuse, abuse, or injury from improper wiring or installation. This warranty doesn't cover incidental or consequential damages. LUTRON’S Legal responsibility ON ANY Declare FOR DAMAGES ARISING OUT OF OR IN CON­NEC­TION WITH THE MANUFACTURE, SALE, Installation, Delivery, OR USE OF THE UNIT SHALL By no means EXCEED THE PUR­CHASE Price OF THE UNIT. This guarantee offers you particular legal rights, and you might have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how lengthy an implied warranty could final, so the above limitations might not apply to you. Patents pending. Lutron, Maestro Wireless, and the Sunburst logo are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American Nationwide Requirements Institute. IEC is a trademark of the Worldwide Electrotechnical Commission. Made and printed in the U.S.A. 25/09/09 P/N 041-172 Rev. A eight ft (2.Four m) 18 x 18 ft (5.5 x 5.5 m) 13 ft (4.0 m) 9 ft (2.7 m) 20 x 20 ft (6.1 x 6.1 m) 14.5 ft (4.Four m) 10 ft (3.0 m) 22 x 22 ft (6.7 x 6.7 m) 16 ft (4.9 m) 12 ft (3.7 m) 26 x 26 ft (7.9 x 7.9 m) 19 ft (5.8 m) Momentary Mounting Strategies 1.1 1.2 Insert the ceiling tile mounting wire via the two smaller holes in the mounting bracket and substitute the mounting bracket. Mount Sensor to a ceiling tile by inserting the wire legs by the tile, ensuring the Sensor is flush to the tile. Word: Do not twist wire legs collectively. 1.2 After the Sensor has been quickly mounted, go away the Sensor in place on the tile and both take the tile down or remove an adjacent tile to realize access to the legs of the mounting wire on the again of the tile. Low Activity: That is essentially the most delicate setting and can detect very slight motions. That is the really helpful setting, as it's going to work effectively for practically all applications. It is good for areas the place occupants will often be seated for lengthy durations of time. Twist the wire legs collectively tightly so the mounting bracket stays snug towards the tile. This setting is barely much less sensitive than the Low Activity setting and can be utilized for areas that expertise regular activity. This is the least delicate setting and can be used for spaces that may generally only expertise massive motions, reminiscent of foot traffic. The Low Activity setting is the default and will perform greatest for many applications. Rarely, if the Sensor is positioned close to exterior noise sources such as heating vents, air conditioning vents, or gentle bulbs, it may flip the lights on with out occupancy or keep the lights on too lengthy after vacancy. If this occurs, altering the sensitivity to Medium Activity or High Exercise ought to resolve the problem. Exchange the tile. Permanent Solid Ceiling Mounting 2.1 2.2 2.Three Superior Set-Up Operation The advanced set-up is accessed by utilizing the buttons on the back of the Sensor. Drill two 3/16 in (4.6 mm) pilot holes for the provided screw anchors. Press the anchors into the holes and tap flush with a hammer. To display the current setting, press and release the specified button. An LED will illuminate briefly, indicating the present setting. Place the flat side of the mounting bracket in opposition to the ceiling and set up the 2 offered screws utilizing a hand screwdriver. To adjust a setting, press and hold the desired button till the LED corresponding to the current setting begins flashing quickly, indicating the setting can now be adjusted. Every subsequent button press of less than 2 seconds will increment the mode to the following out there setting. Urgent any of the other buttons will have no impact. To save the chosen setting, press and hold the button until the LED turns on strong, indicating the saved setting. During the adjustment process, if there isn't any activity for 30 seconds, the LEDs will turn off and no settings can be saved. Notice: Do not over-tighten. 2.4 Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise course until the Sensor locks into place. To take away the bracket from the ceiling, grasp the elimination tab on the adhesive strip and pull the tab VERY SLOWLY straight throughout the ceiling, stretching the strip until the bracket releases from the ceiling. Discard the strip. By no means pull the strip at an angle, as it could break or damage the ceiling floor. Be aware: Do not pull at an angle. Lens Masking (Optionally available) Each time doable, the Sensor needs to be put in in a location where it cannot easily see into areas exterior the meant space, resembling hallways or adjacent rooms. If this example cannot be averted, portions of the lens may be masked with the supplied labels to block the Sensor’s view of the undesired areas. It's endorsed to take away the Sensor from the mounting bracket before making use of Advanced Set-Up (Optional) the masking labels. The Sensor features a number of superior set-up modes. For the vast majority of installations, the default settings will provide the very best performance and also you will not have to utilize the advanced set-up. The Occupancy model of the Sensor has three adjustable superior set-up modes: Timeout, Auto-On, and Sensitivity. The Vacancy-Only model has solely two modes (Auto-On not obtainable). The default settings are listed beneath. The Sensor could be screwed onto the mounting bracket in a number of different orientations. Be sure to note the Sensor’s orientation before taking it down and substitute the Sensor in the same orientation to ensure the meant area will get blocked. Outer lens sections correspond to the detection areas furthest away from the Sensor, whereas internal sections correspond to areas closer to the Sensor. Watch out when making use of the labels to avoid creating gaps between adjoining masked sections. The Sensor may detect movement by means of inadvertent gaps. All the time (Occupancy version solely) Timeout 30 min 15 min 5 min Auto-On Always Low mild Disable Exercise Timeout 30 min 15 min 5 min Advanced Set-Up Modes Auto-On At all times Low mild Disable Exercise Activity: Low Activity Lens sections shown in white are masked with labels Timeout The Sensor will turn the lights off if no motion occurs at some stage in the timeout interval. There are three out there timeout settings: 5, 15, and 30 minutes. Lens Mask Lens sections shown in gray haven't been masked Auto-On The automatic-on functionality of the Sensor may be adjusted to regulate how the lights reply upon initial occupancy. There are three out there settings: All the time, Low gentle, and Disable. All the time: The lights will always activate. Testing Sensor Protection With the Sensor mounted on the ceiling, press and release the "Test: Sensor" button on the entrance of the machine. The lens will glow briefly, indicating the check mode has been entered. Observe: There's a heat-up period of approximately forty seconds after the batteries are installed before the check mode could be activated. If the button is pressed throughout this time, the lens will flash repeatedly until the warm-up interval is complete, after which the test mode can be automatically entered. Confirm the coverage area by walking through the area and observing the lens. The lens will glow solid every time movement is detected. If the lens remains off during motion, the Sensor can not detect movement at that location. Press and launch the "Test: Sensor" button once more to exit the take a look at mode. If the button is not pressed, the check mode will robotically day trip quarter-hour after being enabled, or 5 minutes after the final detected movement if the room is vacated. If the Sensor has important hassle detecting movement during the check, it needs to be moved to a different location and retested. If the Sensor still has poor detection from the brand new location, refer to the Troubleshooting section. Non permanent Drop Ceiling Mounting Use this procedure if the Sensor will probably be mounted on a ceiling tile. The ceiling tile mounting wire is provided for both temporary and everlasting mounting of the Sensor to drop ceilings composed of multiple tiles. It is designed to allow short-term mounting, testing, and repositioning (if vital) of the Sensor with out damaging a ceiling tile. Once the Sensor’s ultimate position has been chosen, the mounting wire will be twisted to lock the Sensor in place permanently. If the Sensor coverage and wireless communication assessments have been successfully completed, use the mounting bracket as a template to mark the screw gap locations with a pencil. Notice: Pull very slowly. Max. Room Dimensions Radius of Coverage for Full Coverage at Ground If you're unsure about appropriately positioning the Sensor, the following momentary mounting and testing procedures are beneficial to confirm proper performance before completely installing the Sensor. Sensor’s detection range is dependent on the ceiling height, as shown in the desk below. Notice: Don't disassemble, crush, puncture, or incinerate the batteries. Don't dispose of batteries in regular household waste. Please recycle, take to a correct battery disposal facility, or contact your native waste disposal provider relating to native restrictions on the disposal or recycling of batteries. O NOT mount the Sensor within 4 ft (1.2 m) of HVAC vents or mild bulbs put in beneath the ceiling line. Hotter rooms could cut back the Sensor’s capacity to detect occupants. Use only high-quality lithium batteries, size CR123, 3 V (ANSI-5018LC, IEC-CR17345). Do not use rechargeable batteries. Using improperly rated batteries may harm the Sensor. For questions concerning the installation or operation of this product, call the Lutron Technical Support Center. Please provide precise mannequin quantity when calling. U.S.A. and Canada (24 hrs / 7 days) Setting the Occupancy Gentle Degree (occupancy model, dimming gadgets only) the Sensor to the mounting bracket by inserting and twisting in a clockwise 2.5 Attach direction until the Sensor locks into place. Sensor coverage and wireless communication assessments as described in 2.6 Perform sections E. Testing Sensor Coverage and F. Testing Wireless Communication. The Sensor should be put in in a location where it has a superb view of all components of the room. The Sensor requires line of sight to operate properly. If you can't see the Sensor, it can not see you. The Sensor can't see by means of glass objects reminiscent of patio or shower doors. The vary and efficiency of the RF system is extremely dependent on quite a lot of complex elements similar to: · Distance between system elements · Geometry of the building construction · Construction of partitions separating system parts · Electrical equipment situated near system parts Technical Assistance 2.2 Identify a location on the ceiling the place the Sensor could have a great view of the room. 2.3 Remove the black "wall side" liner from the adhesive strip. The Sensor is designed for ceiling use only. Do not set up on ceilings higher than 12 ft (3.7 m) or non-ceiling surfaces. Doing so might considerably inhibit the Sensor’s efficiency. 4. Do not paint Sensor. · · · · The "Lights On" and "Lights Off" buttons ought to now switch the lights in the room on and off, respectively, when pressed. Repeat the above process to arrange the Sensor with any further gadgets. The Sensor is meant for indoor use only. Operate between 32 °F and 104 °F (zero °C and 40 °C). 1.1 several seconds. Sensor that has been set up. After roughly 6 seconds, the lens will flash quickly a number of instances, indicating the sunshine degree has been saved. All Sensors arrange with the Dimmer will now use the saved occupancy mild stage. 2. Clear Sensor with a comfortable damp cloth only. Don't use any chemical cleaners. Notice: This equipment has been examined and found to adjust to the bounds for a category B digital machine, pursuant to half 15 of the FCC rules. These limits are designed to supply cheap protection towards dangerous interference in a residential installation. This gear generates, uses and might radiate radio frequency vitality and, if not installed and used in accordance with the directions, could cause dangerous interference to radio and tv reception, which can be decided by turning the equipment off and on. The user is inspired to attempt to appropriate the interference by one or more of the next measures: Reorient or relocate the receiving antenna. Enhance the separation between the gear and receiver. Connect the gear into an outlet on a circuit completely different from that to which the receiver is linked. Consult the seller or an experienced radio/Tv technician for assist. Caution: Changes or modifications not expressly accepted by Lutron Electronics Co. may void the user’s authority to function this equipment. This system complies with Part 15 of the FCC guidelines. This machine must settle for any interference received, including interference which will trigger undesired operation. Switch 2.1 Set the Dimmer to the desired mild level for getting into the room. 2.2 Save holding the "Lights On" button on the entrance of a Observe: For either Sensor model, the lights can also be manually turned off at any time by using the dimming or switching machine immediately. Important Notes or Add the Sensor to the Dimmer or Change by urgent and holding the "Lights Off" button on the entrance of the Sensor for approximately 6 seconds until the lens flashes briefly. The lights within the room may also flash three times, indicating the Sensor has been efficiently added. The Dimmer or Change will exit set-up mode routinely. The sensitivity of the Sensor might be adjusted based mostly on the expected stage of activity within the room. There are three accessible activity settings: Low Activity, Medium Exercise, and High Exercise. Everlasting Drop Ceiling Mounting Be aware: Depart the removing tab uncovered previous the sting of the bracket so it can be accessed for elimination later. 6 seconds till all LEDs on the device begin flashing. Launch the tap button. Sensor is detecting movement in areas that are not desirable, akin to hallways or adjoining rooms, consult with part I. Lens Masking. If Sensor detection is passable throughout this test, perform the wireless communication check as described in section F. Testing Wireless Communication. Testing Wireless Communication This check needs to be performed to confirm that the Sensor has been accurately arrange with the corresponding dimming or switching gadget and that there is correct wireless communication from the chosen Sensor location. If the lights within the room are usually not on, turn them ON manually on the dimming or switching system. Press and release the "Lights Off" button on the front of the Sensor. The lights should turn OFF. Press and launch the "Lights On" button on the entrance of the Sensor. The lights should turn on. If the lights don't respond appropriately, seek advice from the Troubleshooting part. Low mild: The lights will solely activate robotically upon entry if there shouldn't be already adequate ambient mild in the room. Hallway falls within Sensor’s coverage area. Disable: This setting converts the Sensor to vacancy mode. The lights will not robotically activate but will nonetheless automatically turn off after vacancy. The lights should be manually turned on by using the associated dimming or switching system. Notice: The 15-second vacancy grace period is active in this mode. Discuss with the Sensor Operation section firstly of this document for extra details. Troubleshooting Symptom Doable Causes Solution Lights don't turn on when house is occupied. Sensor shouldn't be correctly added to dimming / switching gadget(s). Sensor’s Auto-On setting is set to "Low light" or "Disable". The lights had been just lately turned off manually and the timeout has not but expired. Sensor does not have full view of room. Sensor is outside wireless range of dimming/switching machine. Confer with section B. Set-Up. Confer with section H. Superior Set-Up. Dimming/switching device has been improperly wired. Light bulb(s) burned out. Breaker is off or tripped. Sensor’s timeout is too brief for this software. Sensor does not have full view of room. Lens mask is improperly utilized. Sensor’s sensitivity is simply too low. Sensor’s timeout has not but expired. An exterior noise supply corresponding to an HVAC vent is interfering. Refer to part A. Pre-Installation. Behavior of lights does not match Sensor settings. Sensor protection extends past room perimeter. The intended setting was not saved. Multiple Sensors are added to a dimming/switching machine and their settings do not match. Check with part A. Pre-Installation. Discuss with part C. Sensor Placement or I. Lens Masking. Discuss with section H. Superior Set-Up. Discuss with section H. Advanced Set-Up. Sensor lens doesn't glow in response to motion during Sensor coverage testing. Sensor can't see movement due to obstruction. Room is too massive or oddly shaped. Move Sensor to another location. Consult with section C. Sensor Placement. A number of Sensors may be obligatory for full room protection. Try transferring Sensor to a brand new location or lowering sensitivity. Check with section C. Sensor Placement or H. Advanced Set-Up. Lights flip OFF whereas house is occupied. Lights keep ON after space is vacated. Lens does not cease glowing during Sensor protection testing even when there is no such thing as a motion. Lights don't respond correctly throughout wireless communication testing. Sensor lens flashes and lights don't turn on when space is occupied. Battery has been installed incorrectly. An exterior noise supply similar to an HVAC vent is interfering. Discuss with section C. Sensor Placement. Consult with part C. Sensor Placement or F. Testing Wireless Communication. Refer to part H. Superior Set-Up. Refer to section C. Sensor Placement. Check with part I. Lens Masking. Refer to section H. Superior Set-Up. Refer to section H. Advanced Set-Up. Strive moving Sensor to a new location or decreasing sensitivity. Seek advice from part C. Sensor Placement or H. Advanced Set-Up. Sensor just isn't correctly added to dimming / switching machine. Sensor is outside wireless vary of dimming/switching device. Refer to section B. Set-Up. Move Sensor nearer to dimming/switching machine and retry test. Consult with part F. Testing Wireless Communication. Battery has been put in incorrectly. Dimming/switching gadget has been improperly wired. Light bulb(s) burned out. Breaker is off or tripped. Battery is low. Seek advice from section A. Pre-Installation. Remove sensor from take a look at mode. Discuss with section E. Testing Sensor Protection. If you loved this information and you wish to receive much more information concerning www.pinterest.com please visit our web site.

Последние объявления

Мой песик